On November 9, 2026, Infineon announced that it had processed 300mm silicon carbide (SiC) wafers into working power devices at its fab in Villach, Austria. The company says it is the first to achieve this in a high-volume manufacturing environment. It did so not on a new SiC-dedicated line but with existing silicon (Si) manufacturing equipment. A 300mm wafer yields 2.3 times as many chips per wafer as a 200mm wafer. However, the timing of the production ramp has not been set and will be planned in consultation with customers and partners.

Key points of Infineon's 300mm SiC announcement
Feasibility at 300mm was confirmed for both device processing and crystal splitting, but production timing is undecided
Chips per wafer (vs. 200mm)
2.3x
From the larger wafer diameter
Device processing site
Villach
Austria, existing Si equipment
Cold Split confirmed at 300mm
Dresden
Germany
Production ramp timing
TBD
To be agreed with customers and partners

Source: Infineon press release (November 9, 2026)

Processed on existing Si equipment

The key point of the announcement is that Infineon used existing Si manufacturing equipment to process SiC at 300mm. SiC is currently in the middle of a transition from 150mm to 200mm, and Infineon itself only signed a 200mm SiC wafer supply agreement with Wolfspeed in October, saying it would shift procurement from 150mm to 200mm. If 300mm tools built for Si can be reused, the burden of equipping dedicated tools for a move to 300mm could be reduced.

Infineon describes 300mm production as technologically more advanced and significantly more efficient than 200mm. The figure it gave in support is the 2.3x chip count that comes from the larger wafer diameter.

On the crystal side, Cold Split confirmed at 300mm

In parallel, Infineon also confirmed at its site in Dresden, Germany, that Cold Split technology can be applied to 300mm SiC. Cold Split is a technology for splitting wafers from a SiC single-crystal ingot (boule); compared with conventional wire sawing, it causes less material loss and takes much less processing time. The company says it yields more wafers from the same crystal with less capital investment.

There is movement among substrate makers on 300mm SiC as well. In September, Resonac announced that it had succeeded in growing and processing a 300mm SiC single crystal. Infineon's announcement shows the feasibility of 300mm at the next stage, device processing.

Recent announcements on 300mm SiC
Feasibility at 300mm has been shown for both substrate crystals and device processing
CompanyStageDetailsDate
InfineonDevice processingProcessed 300mm SiC wafers into working power devices at the Villach fab (using existing Si equipment)November 9, 2026
InfineonWafer splittingConfirmed Cold Split technology for 300mm SiC in DresdenNovember 9, 2026
ResonacSingle crystalSucceeded in growing and processing a 300mm SiC single crystalSeptember 15, 2026

Source: Infineon press release (November 9, 2026). Resonac from a previous Sector Signals article (based on the company's announcement)

Si, GaN and SiC all on 300mm

On October 27, Infineon announced that it would build a fab in Villach to mass-produce GaN power semiconductors on 300mm wafers for about 1.1 billion euros. The company describes the new SiC result as extending its 300mm efforts to a second wide-bandgap material. CEO Jochen Hanebeck commented that with silicon, gallium nitride and now silicon carbide 300mm wafers, Infineon is positioned to scale manufacturing and deliver profitable growth.

On the demand side, after listing traction inverters, onboard chargers, EV chargers, large-scale energy storage, industrial drives and uninterruptible power supplies as SiC applications, the company said that in AI data centers, new roles for SiC are emerging in solid-state transformers (SSTs), circuit breakers and power supply units (PSUs), driving demand growth.

What it means for procurement and design teams

  • 200mm remains the mainstay for now: Infineon says it will decide the timing of the 300mm ramp in consultation with customers and partners, and its 200mm manufacturing roadmap continues. It is realistic to build procurement plans for the next few years around 200mm
  • 2.3x the chips does not translate directly into unit price: 2.3x is the number of chips per wafer; no outlook was given for unit prices including yield and crystal and equipment costs
  • It is useful in price negotiations: Reusing existing Si equipment and getting more wafers per crystal with Cold Split both point toward lower SiC costs. When discussing medium- to long-term pricing terms, it is worth confirming the 300mm production timeline with the supplier
  • What was not disclosed: The voltage rating and type of the processed devices, yields and the source of the 300mm SiC substrates were not included in the announcement

Referenced Fact Cards